Drone with Camera > DJI Drone Footage  > DJI FPV SYSTEM LIVE VIDEO OUTPUT – V1 & V2 GOGGLES WITH AIRUNITS
guru
Comments:
  • Rene Kreher
    May 11, 2022 at 9:23 pm

    can we get full hd out or its only hd?

  • Estudio Aguila Magnetica
    May 11, 2022 at 9:23 pm

    Hello! Do you know how to activate the live sound on the dji air unit, with the v2 goggles? I connect my headphones but I have no audio…

    Thanks for your video. Greetings!!

  • Paulo Lobo
    May 11, 2022 at 9:23 pm

    It needs the onscreen information on hdmi out, if it does not have it will have no use…

  • 赖竞豪
    May 11, 2022 at 9:23 pm

    how to get osd on PC?

  • C Lawson
    May 11, 2022 at 9:23 pm

    You're a content creator…… Please just remove your props to save the young ones fingers and eyes.

  • ZTAG RC
    May 11, 2022 at 9:23 pm

    We can livestream with digiview now! check it out: https://youtu.be/GyofZ6y8WlY

  • choppergirl
    May 11, 2022 at 9:23 pm

    POST THE COMPUTER HARDWARE AND GRAPHICS CARD YOU ARE USING TO DECODE THE STREAM PLEASE.

  • choppergirl
    May 11, 2022 at 9:23 pm

    How the hell are you guess getting near zero latency? When I run it I get 3 seconds or 3000ms latency…

    I an move my hand in front of the camera and count 3 mississippies before it will move on the screen… and I'm running the Low Latency Experimental version or the regular version. My display is set to 1080p, but I tried changing it to 720p and the hack won't even run at all then. It's very flakey, most of the times when you start it it just crashes… I have to run it from a command prompt so the DOS window won't close and I can read the error messing.. which usually says increase propebize it couldn't get enough frames to estimate something.

    It took me weeks to finally getting this working… and one destroyed computer in the process during Win10 upgrade… you need Win 8.1 or higher to run node.js.

    3 seconds latency for me… :-/ I could snap my fingers and wait 3 seconds until I see it on screen,t here is no instantaneous snap like going on here… on the bench, 50mbs enabled.

    Is it your CPU? Is it because you have automatic recording turned off? What is going on for you to get this kind of instantaneous 150ms or less latency…

  • Pandacat 666
    May 11, 2022 at 9:23 pm

    IN YOUR FACE DJI!!! you money gready bastards

  • simon wood
    May 11, 2022 at 9:23 pm

    I have this working on my android phone… But wanted to get it on my ipad… Can't see an app for that…. But I connected my phone to the Googles…. Video on the phone from the Googles then streamed it to the ipad by hotspotting the ipad from my phone. Did this because I allready had an ipad and didn't want to buy an android tablet just as a viewer… Plus you can screen share your flight to any of your friends live through Facebook chat

  • ЯПравоQator
    May 11, 2022 at 9:23 pm

    hello today, the picture from the air unit disappeared. in the v2 glasses, the inscription appeared : image transmission signal lost. what to do?

  • choppergirl
    May 11, 2022 at 9:23 pm

    You need Windows 8.1 or higher just to install and run node.js (first instruction line in the Readme, text file, in case you completely skipped it and watched ItsBlunty's video where he failed to mention it)

    Supports 2 out of 16 versions of Windows… that's what happens when you rely on software written by people who have no clue how important backwards compatibility is. I'm going to have to upgrade an All in One PC to Windows 10 (which I hate and don't use) just to try and use this hack.

    I mean, it is beta, and not the hackers fault, they're just trying to establish a beach head and getting working… but it would be nice to see that rubbish written out of some version of the software… because a lot of people are going to want to run it on android boxes that do not run Windows or old Windows XP laptops they want to repurpose for this.

    So… why not node.js? Because node.js requires Windows 8.1 and higher, that's why not 🙂

    The main goal should be able to run the stream full screen and get that latency down as low as possible, so that people can fly to it. The latency is probably happening inside the goggles and there's not much that can be shaved off of it beyond a certain point… might help to turn goggle DVR recording off, that might free up some cycles, or cap the bit rate? Or set the air unit to record only at 720p too, or not at all. Things to try all in the name of getting complete frames to your 23" screen that much faster.

    I sure as h3ll don't want to fly to those 2" screens inside the DJI goggles.. I can't stand them.

  • Paulo Pang
    May 11, 2022 at 9:23 pm

    When we'll have audio live?

  • a h
    May 11, 2022 at 9:23 pm

    Does the website work on computer only or can I use iPhone ?

  • Ryan
    May 11, 2022 at 9:23 pm

    So what did this video add to the scene? Seriously asking why you made this video? Just to try and grab some views from the hype?
    And why the hell do you keep calling it the "Raspberry P – I"? It's Pie. I know they spell it Pi, but its pronounced Pie.
    This is a hack. They sniffed the "magic bytes" sent by the smart controller in order to send them from custom software. The application is sending these "magic bytes" to the goggles to trick them into sending out the data. Saying it "isn't a hack" just because you don't like the dirty word doesn't make it so.

  • Emilio's Journeys
    May 11, 2022 at 9:23 pm

    Not Working!! At least for me lolol. I turned auto temp off and even lowered the mw to 25 . I have good usb C data cable still nothing on lolol maybe I should try another usb cable but as is all these beta things are a touch and go

  • Cristián González
    May 11, 2022 at 9:23 pm

    Hello!!

    Device: CristalSky
    Model Number:CS785
    System Version: 03.00.02.00
    Kernel Version: 3.10.0

    Try: Upload Digiview_0.1._0_ALPHA.apk via:
    A.- SD Card1: "Parse Error; There was a problem parsing the package"
    B.- Via USB, debug Mode; ADB: " [INSTALL_FAILED_OLDER_SDK] "

    Do you think its possible to feed the cristal sky ?, or too soon, tnks in advance.

  • TYPE xxi - WOLF
    May 11, 2022 at 9:23 pm

    I have now a serious question: you have the FPV drone therefore the FPV goggles V2 but you are showing the live feed from the dji airunit or caddx airunit I guess.

    Or is it a Goggles V1 – air unit setup ?

    I had thought the Goggles V2 could no longer bind to an air unit and therefore the Goggles V2 were dead for me as the DJI FPV remote V2.

    Are the FPV remote V2 and Goggles V2 using with the dji air unit and caddx vista air unit ?

    I'm so confused or must have missed the news that the V2 goggles are now supporting everything – except Air 2S and all cinematic drones before. It becomes more and more strange.

  • TYPE xxi - WOLF
    May 11, 2022 at 9:23 pm

    android app shall be out according to AndyRC but I guess you will have noticed that for sure – but in case not now you know !

    NOT TO FORGET: you have cracked the 19K subscriber !
    Congratulations – and now the 20K is no longer that far away

  • Bodek's RC
    May 11, 2022 at 9:23 pm

    Near future is already here!!! The app on android is out ! 😁😄 Thanks for all this hard working smart ppl 👍👍👍👌👌👏👏👏👏💪💪

  • Bodek's RC
    May 11, 2022 at 9:23 pm

    Near future is here!!!😄 App for Android is already here 😁😁😁 Thanks for all this hard working smart ppl 👍👍💪💪👏👏👏👏

  • Checkered Flag Films
    May 11, 2022 at 9:23 pm

    Have you tried it with the (android) Crystal Sky Monitor? IMO…that would be monumental!!…if it did work.

  • Ranubis Amadeus Wolfgang
    May 11, 2022 at 9:23 pm

    GOOD CONTENT BUDDY! I'M SUBBING YOU! 😍😍😍😍😍😍

  • Gmi Visuals (Jason)
    May 11, 2022 at 9:23 pm

    Android app now available

  • Andrew Ferry
    May 11, 2022 at 9:23 pm

    I hope some brilliant people can hack the hell out of these goggles.

  • TYPE xxi - WOLF
    May 11, 2022 at 9:23 pm

    there is no visible delay or lag from here.

  • Flore Flyer
    May 11, 2022 at 9:23 pm

    Rasberry pi version works and has been released by Cosmo Streamer, I have it on my Pi and it outputs on the Pi HDMI socket, I've used it with both a monitor and also my FatShark dom3 goggles.

Leave a reply